mooring Archives - Adventures in Oceanography and Teaching

So in my previous post we deployed a mooring (in fact, those pictures were from the deployment of several different moorings). Now how do we get such a monster back on board again?

Recovering a mooring is always slightly nerve-wracking, because even though we’ve tried very hard to forget about this possibility during the year the mooring was out there in the ocean, it is never 100% certain that we will actually be able to recover it. It might not be there any more, or it might be out of batteries. I have been on cruises where we have had to give up on recovering moorings, or on another one where we had to dredge for a mooring (and found it!). Luckily, on this cruise things went smoothly and the way they were supposed to:

A sound signal is sent and establishes contact with a releaser that connects the anchor with the rest of the mooring. After establishing the position of the mooring, a signal is sent and the releaser lets go of the anchor: The mooring floats up to the surface!

Then, the task is to spot the orange floatation thingies in the waves.

And bring the ship close enough to actually connect a hook to it.

Once it is on the hook, it needs to be brought on board.

Remember, it’s hundreds to thousands meter of rope we are talking about! Luckily the Håkon Mosby is (as all research ships are) equipped with plenty of winches and cranes and a super helpful, knowledgeable and skilled crew.

Instruments are brought on board individually (or, in this case, a releaser).

After having been out in the ocean for a year or two, they are sometimes overgrown with stuff. And in this particular case, that bio stuff was stinky!

But pretty, I have to admit. I think it’s some sort of cold water coral. I think. Any biologists here?

But there is always a lot of stuff to be recovered.

And also pretty interesting: This is the first time I got a good look into one of those orange flotation thingies. I knew there was a glass sphere inside, but it was nice to actually see one. I had previously seen one that had imploded – it ended up pretty much pulverized. But so this is what we knock around on deck and throw out into the ocean:

But yeah. In a nutshell, this is how moorings are recovered.

Do you want to know the full story behind the rope in the mystery picture the other day? On the recent Håkon Mosby cruise, we did a lot of mooring work, and that rope was part of a mooring that we recovered after it has been out in the Iceland Sea for two years.

So what are those moorings all about? The idea behind moorings is that it is super expensive to go out on research ships and that you can only stay out for a fairly short period of time compared to the amount of time you would like to cover with measurements. Therefore, installing instrumentation in the sea and leaving it out there for extended periods of time to measure and store data without anyone being close by, looking after it, gets you a lot of data that you could otherwise never obtain. Once a mooring is in the water, there is no communication with it at all until, after a year or two, we come back to pick up the instruments, read out the data and start on the science.

Moorings basically consist of a lot of rope. They are one or more long pieces of rope held down to the sea floor by a large metal anchor and then pulled in an upright position by large buoys that float at some depth underneath the sea surface. And then there are lots and lots of instruments attached to the ropes at different depths, most with their own buoyant orange floatation thingies [technical term] attached so that, if the ropes broke accidentally, they would float up to the surface and there is the (tiny) chance they might be recovered.

Below is a sketch of a mooring on the Kögur section (And check out the website http://kogur.whoi.edu for tons of information on that section!) to give you an idea of what those things look like (thanks, Kjetil, for letting me use the sketch, and thanks, Steinar, for the awesome work!). I was actually on both the cruise deploying that mooring in 2011 and recovering it in 2012 – check out the cruise blogs for those cruises, well worth a read even years later!

So now without further ado: on to deploying a mooring!

Before a mooring can be deployed, though, a lot of work goes into preparing ropes of the correct lengths with shackles in between where instruments or floatation thingies go.

On the day the mooring is deployed, instruments get attached to the ropes in the correct spots, so they end up at the right depths in the water.

Since moorings are typically several hundred to thousands of meters long, instruments and floatation thingies cannot be attached beforehand and the whole thing then just be thrown out into the water. Instead, when a part of the mooring is ready, out it goes into the sea to make room on deck for the next one to be prepared to avoid creating a gigantic knot filled with very expensive instrumentation.

The whole thing has to be very well coordinated, since there are several cranes and winches involved, and many expensive instruments that are all to end up at a specified depth to measure specific features.

Below we see orange buoyancy floatation thingies being lowered into the sea, and still on deck there is an acoustic current meter that will be next.

One thing I found super interesting on this cruise was to see the different generations of instruments all in use. For example, what we see being lowered into the sea in the picture below, above those orange flotation thingies, is a rotating current meter, predecessor to the acoustic current meter we saw in the image above. Rotating current meters work pretty similar to how we measure wind at home weather stations: The red vane will position the instrument in the current and the little wheel will turn with the current. Both the orientation of the instrument and the rotations of the wheel will be recorded.

When all the instruments and orange floatation thingies are attached to the rope and it has all been lowered into the sea, everything is still floating on the surface. The final act is to drop the anchor that will pull everything under water and in an upright position. This, again, requires a lot of precision, because where the anchor is dropped determines the position in from all the data is going to be collected. So the way this works is that the ship is steaming pretty slowly towards the target position while instrumentation, floatation thingies and rope go over board, and if everything is timed well, by the time everything is out in the sea, the final position has been reached and the anchor can go out.

Exciting stuff! One mooring we even deployed before breakfast (and I am showing this mainly because I like the colors in this pic).

Next post will be on: So now how do we get those things back on deck again after their stint out at sea?

Adventures in Oceanography and Teaching

Dr. Mirjam S. Glessmer

Tag Archives: mooring

Recovering an oceanographic mooring

Deploying an oceanographic mooring