How will lee waves look differently if we are using the asymmetrical mountain instead of the symmetric one? And is symmetry actually important at all or are we just looking at different slopes downstream while the upstream slope doesn’t have an influence on the wave field?

After admitting I had only ever used the symmetrical mountain to generate lee waves in the long tank in the GFI basement, I had to try the asymmetrical one!

There are a couple of reasons why I had not done that before:

• It’s longer (1.5 m instead of the 1 m of the other mountain), therefore the tank is, relatively speaking, shorter. And since being close to the ends of the tank leads to weird interferences, this limits the distance over which observations can be made
• Since it’s asymmetrical, pulling one way or the other would likely show different wave fields, so you couldn’t just run it back and forth and have students observe the same thing several times in a row

But then it would be really interesting to see what the difference would be, right?

I tried two different stratifications.

Weak stratification, shallow water

Since I just wanted a quick idea of what this mountain would do, I used leftover water I had prepared for the moving mountain experiment. Since there wasn’t a lot left, I ended up with 11.5 cm fresh water, but only 4 cm salt water at approximately 20 psu (since I stretched the 35 psu a little).

What I noticed: A LOT more mixing than with the other mountain! Stratification is pretty much destroyed after the first run, usually we run back and forth a lot. This can be for several reasons:

• The water is very shallow, meaning mixing is happening over the whole water column. It might not actually be more mixing than in the other case, but since it’s affecting the whole water column, it might just seem like more because no clearly visible stratification is left above and below the layer which is mixed by the mountain?
• The left side of the mountain was bent up a little (as in 2 or 3 cm), meaning that especially on the way back it was flapping up and down on the upstream side, doing a lot of mixing that wasn’t due to the shape of the mountain, just of bits of it being loose.

And the shape of the “reservoir” that is being built up upstream of the mountain is different to what I have observed before: Running in either direction, the reservoir didn’t built up smoothly, but as a hump that was pushed in front of the mountain. Maybe because the internal wave speed in this case was very close to the speed of the mountain, something like 7cm/s, so the disturbance created by the mountain couldn’t propagate upstream. Is that an upstream hydraulic jump we are seeing there?!

What’s also cool: Lee waves are now not only happening as internal waves, but you see a very clear signature in surface waves! Usually all we see are surface convergences and divergences, adjusting the surface layer to the internal waves underneath. That we now see surface waves is, I am assuming, mainly due to the shallow water relative to the height of the obstacle.

Since I was not satisfied with this at all, I ran a second experiment:

Strong stratification, deep water

First, I tried to set up the same stratification as for this lee wave experiment with the symmetrical mountain because I thought that would be easiest to compare. But I aborted that after having moved the mountain just a little because it was mixing so much that there stratification was destroyed completely and nothing could be seen. I ended up putting more dense water in and ended up with 12 cm pink (35 psu) and 4 cm clear freshwater. And this is what this looked like:

You now see a wave train with wave lengths longer than in the symmetrical case. Probably due to the longer length of the obstacle (even thought the waves are still shorter than the obstacle)? Or what sets the wavelength?

This time, with a faster internal wave speed of around 10cm/s while the mountain is still pulled with 7cm/s, we don’t see the “hump” in the upstream reservoir — the signal can propagate faster than the mountain and thus smoothes out.

So that is what I think is going on here. While the first experiment mainly showed effects of the stratification compared to previous experiments, the second one might provide some insight on the different slopes of the mountain, although I am not sure in what way. Do you see something I didn’t observe? How would you expect the different slopes to influence the lee waves?

I am so glad I tried this and I’m looking forward to thinking about this more! :-) Any insights you’d care to share with me?